Home > Antennas / Mounts > Mounts
Select a category
Ball / Dome Mounts / Roof / Surface Flat / Surface Mounts
Hood , Channel, Door, Trunk Magnet Mounts
Mirror Mounts Misc. Mounts
Side Mount Stake Hole
Sort By:
Page of 3
FireStik Hood/Trunk/Hatch Channel Mounts SS-274A
FireStik Hood/Trunk/Hatch Channel Mounts SS-274A
Price: 21.49

FireStik Hood/Trunk/Hatch Channel Mounts SS-274A.These mounts were specifically designed for hood, trunk and hatchback applications!
Once you have it in your hand you will see the numerous possibilities. All bracket parts are made of stainless steel.
FireStik Extended Stake Hole Mount w/Stud
List Price: $25.95
Price: 19.99
Savings: $5.96

Those square holes in the bed rails of full size pick-up trucks are the prefect location for a no-holes" antenna mount. The flat upper bracket is 6" (152mm) long and extends out over the bed rail so you may mount your antenna without losing the ability to mount a camper shell. Includes stud mount
FireStik Hood/Trunk/Hatch Channel Mounts SS-274
FireStik Hood/Trunk/Hatch Channel Mounts SS-274
Price: 19.49

FireStik Hood/Trunk/Hatch Channel Mounts SS-274. These mounts were specifically designed for hood, trunk and hatchback applications! This is our most versital mount and will work with most vehicles and most channel openings because of the adjustability of the bracket.
FireStik Extended Stake Hole Mount w/Stud for Firewire or Crimp on
List Price: $25.95
Price: 17.99
Savings: $7.96

Those square holes in the bed rails of full size pick-up trucks are the prefect location for a no-holes" antenna mount. The flat upper bracket is 6" (152mm) long and extends out over the bed rail so you may mount your antenna without losing the ability to mount a camper shell. Includes stud mount for Firewire or crimp on coax cable
FireStik "Widget" Swivel Bracket Mounts WSB-4A
FireStik "Widget" Swivel Bracket Mounts WSB-4A
Price: 16.99

FireStik "Widget" Swivel Bracket Mounts WSB-4.  The mounting stud attaches to a chrome plated swivel bracket allowing the antenna angle to be adjusted perpendicular to the mounting plane. This allows the antenna angle to be corrected with the mount on the left or right edge of a trunk, hatchback or bumper. Hardware and mounting stud included. 
FireStik Stainless Steel Stake-Hole Mount
List Price: $16.99
Price: 16.99

This stainless steel mount locks into any of the stake hole pockets along the edge of a pick-up truck bed. There is no need to drill any holes in the vehicle. The mount can be used on bed rails with protective covers (such as those on the newer Ford Super-Duty trucks). Because of the stud mount configuration on this mount, it can only be used on trucks where there is inside access to the stake hole pocket (from side or bottom) for the coaxial cable to be routed to the mount. In some cases, this might require that the coax be routed through an opening that is too small for a PL-259 connector to pass. In those cases, the PL-259 will need to be installed after the coax has been routed. The mount will easily support heavy-duty antennas up to 4 feet (1.2m) in length.
FireStik Dome Mount DM-4A
FireStik Dome Mount DM-4A
Price: 16.99

FireStik Dome Mount DM-4.  As you would expect, Firestik takes the popular Dome Mount to the next level!
FireStik Dome Mount DM-4
FireStik Dome Mount DM-4
Price: 15.99

FireStik Dome Mount DM-4.  As you would expect, Firestik takes the popular Dome Mount to the next level!
L-Bracket Side Mount (Stainless Steel)
Price: 15.49

If you know that your installation will not require the clamping bracket that is supplied with the 3-way mounts, you can save a couple of dollars with these mounts. All of these mounts are specifically used for mounting antennas to a flat vertical surface, such as the side of a van or motorhome. 
FireStik "Widget" Tilt Plate Mount WTP-4
FireStik "Widget" Tilt Plate Mount WTP-4
Price: 14.99

The mounting stud sits on a chrome plated steel plate which is adjustable parallel to the mounting plane. The WTP series works great on metal rain gutters, upper edges of trunks and hatchbacks and also on the top edge of bumpers. Hardware and mounting stud included.